Alcomate Plus Personal Alcohol Breathalyzer Kit

AlcoMate Plus

Personal Alcohol Breathalyzer Kit

MSRP: $135.99

Sale Price: $114.99

Availability: Usually ships the same business day.

Breathalyzer with Replaceable Calibrated Sensor Module
No Calibration Service required!

Features
Precalibrated Sensor Modules
5 Mouthpieces
User's Manual
Vinyl Pouch
Auto Power Off
2 AA Batteries
1 Year Manufacturer's Warranty
FIELD TEST CASE

NOTE: When using the AlcoMate Plus, you may see a "Flo" message in the display. This is an "insufficient airflow" warning, and it means that you are not blowing hard enough.

--------------------------------------------------------------------------------

Replaceable Precalibrated Sensor Module

For AlcoMate Plus

Our Price: $29.95

--------------------------------------------------------------------------------

AlcoMate Plus
No Calibration Required:
Precalibrated Sensor Modules

FDA 510(k) Certified
NF/CE Mark
DOT/NTHSA Approved
Meets US Coast Guard Requirements
Accuracy: +/-0.01 at 0.10% BAC
Hand strap, leather pouch, batteries included
Deep-lung air sampling system
Pressure sensor system
One-way air mouthpiece
Auto Power-Off
1 year warranty

The AlcoMate Plus offers the latest in cutting-edge breath alcohol sensing technology as well as powerful and convenient features.

What is a "Pre-Calibrated Replaceable Alcohol Sensor Module"?
One of the main problems with using breathalyzers in critical applications is that the alcohol sensor, no matter what type, requires periodic re-calibration. Unfortunately, the re-calibration process requires that the breathalyzer be physically mailed or taken to a professional service center, at which point the device must be evaluated and proper steps must be taken for calibration with an expensive simulator system. The process is costly for both consumer and service center, and the delay of processing and shipping back-and-forth can be quite a loss. The Pre-Calibrated Replaceable Alcohol Sensor Module can eliminate the delays and complications of re-calibration by allowing you to simply "snap out" an old module and "snap in" a new module. This way, you can get back to reliable, accurate testing in a matter of seconds!

How do I install a Pre-Calibrated Alcohol Sensor Module?
For the AlcoMate Plus, please take the following steps to install a new sensor module

Prepare your AlcoMate Plus. Make sure it is powered off.	Remove the battery cover.	Remove the batteries.
Using a screwdriver, remove both screws under the battery cover.	Using a screwdriver, remove both screws under the battery cover.	Pull the two tabs (to the left and right of the battery compartment) up from the device.
Pull the two tabs (to the left and right of the battery compartment) up from the device.	Lift up the entire back portion of the device.	Remove the back portion from the device.
Remove the circuit board (with sensor and breath tube attached).	Hold the breath tube where it is attached to the sensor module.	Remove the breath tube from the sensor module. It should lift easily.
Pull the sensor module up from the adapter slot. Be careful.	Re-attach the breath tube, as shown.	Replace the circuit board to its original position.
Press firmly to make sure that the new sensor module is secured in place.	Re-attach the breath tube, as shown.	Replace the circuit board to its original position.
Snap the back portion of the device back on to the front, securely.	Use a screwdriver to remount the screws.	Replace the batteries.
Finally, replace the battery cover.	Ready for Testing!

Click Here to Order

or call

702-289-5408

Viper Technologies offers its products for legal use only. It is the sole responsibility of the purchaser to determine local, state, federal, and international regulations prior to purchase.Viper will not be held responsible for any illegal use of its products. Viper reserves the right to refuse shipment to any person/party for any reason. Specifications and prices listed on the Viper web site and in Quotes are subject to change without notice. All images and brand names of products are either copyrightViperI or are copyright or trademark of their respective companies. Viper reserves all rights. All other companies reserve their respective rights. No part of Viper's online or offline data may be copied without the express written consent of Viper and / or the copyright / trademark owner.

Most Viper products and item components are subject to Export restrictions administered by the US Departments of State & Commerce. Please contact the US Department of State / Commerce for assistance. If Export of any component or item of Viper's products are approved by the United States Government, Re-Export laws must be complied with.